This How-To shows how you will install 3CX on the entry level appliances of the APU2 line.
- in general all those of the APU2 line
- Prepare the key as shown in our article: Prepare the bootable USB drive for 3CX
- An ethernet cable inserted into the APU2 device in the NiC near the COM that is working and with the possibility to go out on the internet
Insert the key into the APU2, connect the COM port and switch on the APU2 by switching on the power supply.
When you get to this screen, choose “install” and click the TAB button to edit
Delete quiet after i – – – and write: console = ttyS0,115200n8. Send to start the installation.
Wait a few more seconds, you will see the boot information flow and then you will get to the actual installation. From here you have to choose all the information to install Debian 9.
If you choose the enp1S0 remember that the physical NiC corresponds to the one near the COM port.
The interface configuration via DHCP will start automatically. If DHCP is not present, or if you prefer to give an IP manually, just press <Cancel> in the following screen.
Here the DHCP Server was not present, so the network configuration fails.
Click on continue and then enter the IP manually. Remember that if there is DHCP you do not have to take these steps
Enter the IP you prefer including the subnet mask, gateway and DNS server and then click on continue.
If the configuration of the Network is successful, and the 3CX has network and internet connection, you can go on, otherwise you will see this error:
By clicking on Continue you will be returned to the main menu with all the steps of the installation. Select again the part of Network, re-enter all the parameters taking care not to make mistakes and then continue with the installation.
If you have passed the part of networking without errors, you will get to the screen to enter the root password (to be repeated 2 times).
Choose English on the following screen
Follow the steps as shown
Choose according to your needs: if you do not know what to choose, go ahead as shown
Choose in disk on which to install the operating system: be careful NOT to choose the USB stick !!
Choose according to your needs,if you do not know what to choose, go on as shown
The installation of the Debian 9 operating system will start and will continue on its own until the end. At the end, remove the key or the installation will restart.
This is the GRUB screen, at the end you will have the prompt to log in to the console
We noticed that, strangely, the switchboard package was not present. It’s not a serious problem because normally a command is enough to install it.
Debian 9 there are two more steps to do. It does not take too much time and it will be enough to follow this guide to complete it.
Unfortunately, there is still no 3cxpbx package in the Debian 9 repositories, so we have to make some minor changes to install it.
First we check if the libcurl3 package is installed:
# dpkg -l | grep libcurl3
If version 18.104.22.168 + deb9u3 is present: remove it because 3cxpbx requires an older version
# apt remove libcurl3
Now let’s proceed to the actual installation by installing the libcurl3 of the old Debian8
wget -O- http://downloads.3cx.com/downloads/3cxpbx/public.key | apt-key add – echo “deb http://downloads.3cx.com/downloads/debian stretch main” | tee /etc/apt/sources.list.d/3cxpbx.list
apt-get install libcurl3 = 7.38.0-4 + deb8u5
apt-get install 3cxpbx
At 99% you will be asked how you want to complete the installation
For simplicity, use option 1 (Web) by clicking 1
Go to the web and complete the installation.
HTTP://<IP DEL VOSTRO APPLIANCE>:5015?V=2
NOTE: If we modify the repository with Stretch, the libcurl3 package will also change at the first upgrade. Do not do this until 3CX releases the package for Debian 9